View ADT6503_7189889.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

low cost, 2.7 v to 5.5 v, micropower temperature switches in sot-23 preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ? 2006 analog devices, inc. all rights reserved. features 0.5c (typ) accuracy over temperature range factory set trip points from ?45c to +15c in 10c increments factory set trip points from +35c to +115c in 10c increments no external components required max temperature of +125c open-drain output (adt6501/ADT6503) push-pull output (adt6502/adt6504) pin selectable hysteresis of 2c and 10c supply current of 30 a (typ) space saving 5-lead sot23 package applications medical equipment automotive cell phone hard disk drives personal computers electronic test equipment domestic appliances process control functional block diagram clk and timing generation 4 3 lpf - digital comparator tover v cc 1 gnd hyst temperature sensor 1-bit 12-bit decimator 1-bit dac reference + ? 5 factory preset trip point register 2 gnd 2c/10c 06096-001 figure 1. general description the adt6501/adt6502/ADT6503/ adt6504 are trip point temperature switches available in a 5-lead sot23 package. it contains an internal band gap temperature sensor for local temperature sensing. when the temperature crosses the trip point setting, the logic output is activated. the adt6501/ ADT6503 logic output is active low and open-drain. the adt6502/adt6504 logic output is active high and push-pull. the temperature is digitized to a resolution of +0.0625c (12 bit). the factory settings are 10c apart starting from ?45c to +15c for the cold threshold models and from +35c to +115c for the hot threshold models. these devices require no external components and typically consume 30 a supply current. hysteresis is pin selectable at 2c and 10c. the temperature switch is specified to operate over the supply range of 2.7 v to 5.5 v. adt6501 and adt6502 are used for monitoring temperatures from +35c to +115c only. hence, the logic output pin becomes active when the temperature goes higher than the selected trip point temperature. the ADT6503 and adt6504 are used for monitoring temperatures from ?45c to +15c only. hence, the logic output pin becomes active when the temperature goes lower than the selected trip point temperature. product highlights 1. 0.5c typical from ?55c to +125c. 2. factory threshold settings from ?45c to +115c in 10c increments 3. supply voltage is 2.7 v to 5.5 v. 4. supply current of 30 a. 5. space-saving 5-lead sot23 package. 6. pin selectable temperature hysteresis of 2c or 10c. 7. temperature resolution of 0.0625c.
adt6501/adt6502/ADT6503/adt6504 preliminary technical data rev. pra | page 2 of 16 table of contents features .............................................................................................. 1 applications....................................................................................... 1 functional block diagram .............................................................. 1 general description ......................................................................... 1 product highlights ........................................................................... 1 specifications..................................................................................... 3 absolute maximum ratings ....................................................... 4 esd caution.................................................................................. 4 pin configuration and function descriptions............................. 5 typical performance characteristics ............................................. 6 theory of operation ........................................................................ 8 circuit information...................................................................... 8 converter details ..........................................................................8 factory programmed threshold range .....................................8 hysteresis input .............................................................................8 functional description.................................................................9 application information................................................................ 10 thermal response time ........................................................... 10 self-heating effects.................................................................... 10 supply decoupling ..................................................................... 10 temperature monitoring........................................................... 11 outline dimensions ....................................................................... 12 ordering guide .......................................................................... 12
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 3 of 16 specifications t a = t min to t max , v dd = 2.7 v to 5.5 v. all specifications for ?45c to +115c, unless otherwise noted. open-drain r pull-up = 100 k. table 1. parameter min typ max unit test conditions/comments temperature sensor and adc threshold accuracy at v cc = 2.7 v to 5.5 v 0.5 6 c t a = ?45c to ?25c 0.5 4 c t a = ?15c to +15c 0.5 4 c t a = +35c to +65c 0.5 6 c t a = +75c to +115c adc resolution 12 bits temperature conversion time 30 ms time necessary to complete a conversion update rate 600 ms conversion started every 600 ms long term drift 0.08 c drift over 10 years, if part is operated at +55c temperature hysteresis +0.03 c temperature cycle = 25c to 125c to 25c temperature threshold hysteresis 2 c 10 c digital input (hyst) input low voltage, v il 0.2 v cc v input high voltage, v ih 0.8 v cc v digital output (open-drain) output high current, i oh 10 na leakage current, v cc = 2.7 v and v oh = 5.5 v output low voltage, v ol 0.3 v i ol = 1.2 ma, v cc = 2.7 v output low voltage, v ol 0.4 v i ol = 3.2 ma, v cc = 4.5 v output capacitance, c out 1 10 pf digital output (push-pull) output low voltage, v ol 0.3 v i ol = 1.2 ma, v cc = 2.7 v output low voltage, v ol 0.4 v i ol = 3.2 ma, v cc = 4.5 v output high voltage, v oh 0.8 v cc v i source = 500 a, v cc = 2.7 v output high voltage, v oh v cc C 1.5 v i source = 800 a, v cc = 4.5 v output capacitance, c out 1 1 10 pf power requirements supply voltage 2.7 5.5 v supply current 30 85 a 1 guaranteed by design and characterization.
adt6501/adt6502/ADT6503/adt6504 preliminary technical data rev. pra | page 4 of 16 absolute maximum ratings table 2. parameter rating v cc to gnd C0.3 v to +7 v hyst input voltage to gnd C0.3 v to v cc + 0.3 v open drain output voltage to gnd C0.3 v to +7 v push-pull output voltage to gnd C0.3 v to v dd + 0.3 v input current on all pins 20 ma output current on all pins 20 ma operating temperature range C55c to +125c storage temperature range C65c to +160c maximum junction temperature, t jmax 150.7c 5-lead sot-23 (rj-5) power dissipation 2 w max = (t jmax ? t a 3 )/ ja thermal impedance 4 ja , junction-to-ambient (still air) 240c/w ir reflow soldering (pb-free package) peak temperature 260c (+0c) time at peak temperature 20 sec to 40 sec ramp-up rate 3c/sec maximum ramp-down rate C6c/sec maximum time 25c to peak temperature 8 minutes maximum 1 values relate to package being used on a standard 2-layer pcb. this gives a worst case ja . refer to figure 2 for a plot of maximum power dissipation vs. ambient temperature (t a ). 2 t a = ambient temperature. 3 junction-to-case resistance is applicable to components featuring a preferential flow direction, for ex ample, components mounted on a heat sink. junction-to-ambient resistance is more useful for air-cooled, pcb- mounted components stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. 0.9 0 125 temperature (c) maximum power dissipation (w) 06096-002 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 ?55 ?50 ?40 ?30 ?20 ?10 0 10 20 30 40 50 60 70 80 90 100 110 120 sot-23 pd @ 125c = 0.107w figure 2. sot-23 maximum power dissipation vs. temperature esd caution esd (electrostatic discharge) sensitive device. electros tatic charges as high as 4000 v readily accumulate on the human body and test equipment and can discharge wi thout detection. although this product features proprietary esd protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. therefore, proper esd precautions are recommended to avoid performance degradation or loss of functionality.
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 5 of 16 pin configuration and fu nction descriptions gnd 1 gnd 2 hyst 3 tover/ tover 5 v cc 4 adt6501/ adt6502 top view (not to scale) 06096-003 gnd 1 gnd 2 hyst 3 tunder/ tunder 5 v cc 4 a dt6503/ adt6504 top view (not to scale) 06096-004 figure 3. adt6501/adt6502 pin configuration figure 4. ADT6503/adt6504 pin configuration table 3. pin function descriptions dt1dt2 pin o. dt3dt4 pin o. nemonic description 1 1 gnd ground. 2 2 gnd ground. 3 3 hyst hysteresis input. connects hyst to gnd for +2 c hysteresis or connects to v cc for +10 c hysteresis. 4 4 v cc supply input (+2.7 v to +5.5 v). 5 C tover / open-drain, active-low output. tover goes low when the temperature of the part exceeds the factory programmed threshold; must use a pull-up resistor. 5 C tover push-pull, active-high output. tover go es high when the temperature of the part exceeds the factory programmed threshold. C 5 tunder / open-drain, active-low output. tunder goes low when the temperature of the part exceeds the factory programmed threshold; must use a pull-up resistor. C 5 tunder push-pull, active-high output. tunder goes high when the temperature of the part exceeds the factory programmed threshold.
adt6501/adt6502/ADT6503/adt6504 preliminary technical data rev. pra | page 6 of 16 typical performance characteristics figure 5. figure 6. figure 7. figure 8. figure 9. figure 10.
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 7 of 16 figure 11. figure 12. figure 13.
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 8 of 16 theory of operation circuit information the adt6501/adt6502/ADT6503/adt6504 are 12-bit digital temperature sensors with the 12 th bit acting as the sign bit. an on- board temperature sensor generates a voltage precisely proportional to absolute temperature that is compared to an internal voltage reference and input to a precision digital modulator. the 12-bit output from the modulator is input into a digital comparator where it is compared with a factory set trip level. the output trip pin is activated if the temperature measured is greater than the factory set trip level. overall accuracy for the adt650x family is 6c from ?45c to +115c. the on-board temperature sensor has excellent accuracy and linearity over the entire rated temperature range without needing correction or calibration by the user. the adt6501/ADT6503 have active-low, open-drain output structures that can only sink current. the adt6502/adt6504 have active-high, push-pull output structures that can sink and source current. on power-up, the output cannot become active until the first conversion is completed. this typically takes 30 ms. the sensor output is digitized by a first-order, - modulator, also known as the charge balance type analog-to-digital converter (adc). this type of converter utilizes time-domain oversampling and a high accuracy comparator to deliver 12 bits of effective accuracy in an extremely compact circuit. converter details the - modulator consists of an input sampler, a summing network, an integrator, a comparator, and a 1-bit digital-to- analog converter (dac). similar to the voltage-to-frequency converter, this architecture creates a negative feedback loop and minimizes the integrator output by changing the duty cycle of the comparator output in response to input voltage changes. the comparator samples the output of the integrator at a much higher rate than the input sampling frequency; this is called oversampling. oversampling spreads the quantization noise over a much wider band than that of the input signal, improving overall noise performance and increasing accuracy. - modulator integrator comparator 1-bit dac lpf digital filter clock generator voltage ref and vptat temperature value register 1-bit 12-bit + ? 06096-005 figure 14. first-order - modulator the modulated output of the comparator is encoded using a circuit technique that results in smbus/i 2 c temperature data. factory programmed threshold range the adt6501/adt6502/ADT6503/adt6504 are available with factory set threshold levels ranging from ?45c to +115c in 10c. the adt6501/ADT6503 outputs are intended to interface to reset inputs of microprocessors. the adt6502/adt6504 are intended for driving circuits of applications, such as fan control circuits. table 4 lists the available temperature threshold ranges. table 4. factory set temperature threshold ranges device threshold (t th ) range adt6501 +35c < t th < +115c adt6502 +35c < t th < +115c ADT6503 ?45c < t th < +15c adt6504 ?45c < t th < +15c hysteresis input the hyst pin is used to select a temperature hysteresis of 2c or 10c. if the hyst pin is connected to v cc then a hysteresis of 10c is selected or if the hyst pin is connected to gnd then a hysteresis of 2c is selected. the hyst pin should not be left floating. hysteresis prevents oscillation on the output pin when the temperature is approaching the trip point, after it activates. for example, if the temperature trip is 45c and the hysteresis selected is 10c, the temperature would have to go as low as 35c before the output deactivates.
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 9 of 16 functional description the conversion clock for the part is generated internally. no external clock is required. the internal clock oscillator runs an automatic conversion sequence. during this automatic conversion sequence, a conversion is initiated every 600 ms. at this time, the part powers up its analog circuitry and performs a temperature conversion. this temperature conversion typically takes 30 ms, after which time the analog circuitry of the part automatically shuts down. the analog circuitry powers up again 570 ms later, when the 600 ms timer times out and the next conversion begins. the result of the most recent temperature conversion is compared with the factory set trip point value. if the temperature measured is greater than the trip point value, the output is activated. the output is deactivated once the temperature crosses back over the trip point threshold plus whatever temperature hysteresis is selected. figure 15 to figure 18 show the transfer function for the output trip pin of each generic model. tth temp tover v 2c hyst 10c hyst cold hot 06096-006 figure 15. adt6501 tover transfer function tth temp t ove r v 2c hyst 10c hyst cold hot 06096-007 figure 16. adt6502 tover transfer function tth temp tunder v 2c hyst 10c hyst cold hot 06096-008 figure 17. ADT6503 tunder transfer function tth temp tunder v 2c hyst 10c hyst cold hot 06096-009 figure 18. adt6504 tunder transfer function
adt6501/adt6502/ADT6503/adt6504 preliminary technical data rev. pra | page 10 of 16 application information thermal response time the time required for a temperature sensor to settle to a specified accuracy is a function of the thermal mass of the sensor and the thermal conductivity between the sensor and the object being sensed. thermal mass is often considered equivalent to capacitance. thermal conductivity is commonly specified using the symbol q, and can be thought of as thermal resistance. it is commonly specified in units of degrees per watt of power transferred across the thermal joint. thus, the time required for the adt6501 /adt6502/ADT6503/adt6504 to settle to the desired accuracy is dependent on the characteristics of the sot-23 package, the thermal contact established in that particular application, and the equivalent power of the heat source. in most applications, the settling time is probably best determined empirically. self-heating effects the temperature measurement accuracy of the adt6501/adt6502/ADT6503/adt6504 can be degraded in some applications due to self-heating. errors can be introduced from the quiescent dissipation and power dissipated when converting. the magnitude of these temperature errors is dependent on the thermal conductivity of the adt650x package, the mounting technique, and the effects of airflow. at 25c, static dissipation in the adt650x is typically tbd w operating at 3.3 v. in the 5-lead sot-23 package mounted in free air, this accounts for a temperature increase due to self- heating of t = p diss ja = tbd w 240c/w = tbdc it is recommended that current dissipated through the device be kept to a minimum, because it has a proportional effect on the temperature error. supply decoupling the adt6501/adt6502/adt 6503/adt6504 should be decoupled with a 0.1 f ceramic capacitor between v dd and gnd. this is particularly important when the adt650x are mounted remotely from the power supply. precision analog products, such as the adt650x, require a well-filtered power source. because the adt650x operate from a single supply, it might seem convenient to tap into the digital logic power supply. unfortunately, the logic supply is often a switch-mode design, which generates noise in the 20 khz to 1 mhz range. in addition, fast logic gates can generate glitches hundreds of mv in amplitude due to wiring resistance and inductance. if possible, the adt650x should be powered directly from the system power supply. this arrangement, shown in figure 19 , isolates the analog section from the logic switching transients. even if a separate power supply trace is not available, generous supply bypassing reduces supply line induced errors. local supply bypassing consisting of a 0.1 f ceramic capacitor is advisable for the temperature accuracy specifications to be achieved. this decoupling capacitor must be placed as close as possible to the adt650x v cc pin. 0.1 f adt650x ttl/cmos logic circuits power supply 06096-010 figure 19. use separate traces to reduce power supply noise
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 11 of 16 temperature monitoring the adt6501/adt6502/ADT6503/adt6504 are ideal for monitoring the thermal environment within electronic equipment. for example, the surface-mount package accurately reflects the exact thermal conditions that affect nearby integrated circuits. the adt650x measure and convert the temperature at the surface of its own semiconductor chip. when the adt650x are used to measure the temperature of a nearby heat source, the thermal impedance between the heat source and the adt650x must be as low as possible. as much as 60% of the heat transferred from the heat source to the thermal sensor on the adt650x die is discharged via the copper tracks, package pins, and bond pads. of the pins on the adt650x, the gnd pins transfer most of the heat. therefore, to monitor the temperature of a heat source it is recommended that the thermal resistance between the adt650x gnd pins and the gnd of the heat source is reduced as much as possible. for example, use the unique properties of the adt650x to monitor a high power dissipation microprocessor. the adt650x device, in its sot-23 package, is mounted directly beneath the microprocessors pin grid array (pga) package. the adt650x requires no external characterization.
adt6501/adt6502/ADT6503/adt6504 preliminary technical data rev. pra | page 12 of 16 outline dimensions pin 1 1.60 bsc 2.80 bsc 1.90 bsc 0.95 bsc 5 12 3 4 0.22 0.08 10 5 0 0.50 0.30 0.15 max seating plane 1.45 max 1.30 1.15 0.90 2.90 bsc 0.60 0.45 0.30 compliant to jedec standards mo-178-aa figure 20. 5-lead small outline transistor package [sot-23] (rj-5) dimensions shown in millimeters ordering guide model threshold temperature temperature accuracy package description package option adt6501arjp035 +35c 4c 5-lead sot-23 rj-5 adt6501arjp045 +45c 4c 5-lead sot-23 rj-5 adt6501arjp055 +55c 4c 5-lead sot-23 rj-5 adt6501arjp065 +65c 4c 5-lead sot-23 rj-5 adt6501arjp075 +75c 6c 5-lead sot-23 rj-5 adt6501arjp085 +85c 6c 5-lead sot-23 rj-5 adt6501arjp095 +95c 6c 5-lead sot-23 rj-5 adt6501arjp105 +105c 6c 5-lead sot-23 rj-5 adt6501arjp115 +115c 6c 5-lead sot-23 rj-5 adt6502arjp035 +35c 4c 5-lead sot-23 rj-5 adt6502arjp045 +45c 4c 5-lead sot-23 rj-5 adt6502arjp055 +55c 4c 5-lead sot-23 rj-5 adt6502arjp065 +65c 4c 5-lead sot-23 rj-5 adt6502arjp075 +75c 6c 5-lead sot-23 rj-5 adt6502arjp085 +85c 6c 5-lead sot-23 rj-5 adt6502arjp095 +95c 6c 5-lead sot-23 rj-5 adt6502arjp105 +105c 6c 5-lead sot-23 rj-5 adt6502arjp115 +115c 6c 5-lead sot-23 rj-5 ADT6503arjn045 ?45c 6c 5-lead sot-23 rj-5 ADT6503arjn035 ?35c 6c 5-lead sot-23 rj-5 ADT6503arjn025 ?25c 6c 5-lead sot-23 rj-5 ADT6503arjn015 ?15c 4c 5-lead sot-23 rj-5 ADT6503arjn005 ?5c 4c 5-lead sot-23 rj-5 ADT6503arjp005 +5c 4c 5-lead sot-23 rj-5 ADT6503arjp015 +15c 4c 5-lead sot-23 rj-5 adt6504arjn045 ?45c 6c 5-lead sot-23 rj-5 adt6504arjn035 ?35c 6c 5-lead sot-23 rj-5 adt6504arjn025 ?25c 6c 5-lead sot-23 rj-5 adt6504arjn015 ?15c 4c 5-lead sot-23 rj-5 adt6504arjn005 ?5c 4c 5-lead sot-23 rj-5 adt6504arjp005 +5c 4c 5-lead sot-23 rj-5 adt6504arjp015 +15c 4c 5-lead sot-23 rj-5
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 13 of 16 notes
adt6501/adt6502/ADT6503/adt6504 preliminary technical data rev. pra | page 14 of 16 notes
preliminary technical data adt6501/adt6502/ADT6503/adt6504 rev. pra | page 15 of 16 notes
adt6501/adt6502/ADT6503/adt6504 preliminary technical data rev. pra | page 16 of 16 notes purchase of licensed i 2 c components of analog devices or one of its sublicensed associated companies conveys a license for the purchaser under the phi lips i 2 c patent rights to use these components in an i 2 c system, provided that the system conforms to the i 2 c standard specification as defined by philips. ?2006 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. pr06096-0- 10 /06(pra)

▲Up To Search▲

Price & Availability of ADT6503

	To Download ADT6503 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .